Liquid-controls SP2900 Bedienungsanleitung

SETTING16 POINTK-FACTOR16 POINTONLYAPPEARSON UNITSWITH16 POINTOPTIONPRESS DISPLAYMENU FLASHES TO DEV TYPLOCKOUTOUTCARDALG OUTOUT FREQRELAY16 POINT(16

SPECIFICATIONSDisplay8 Digit, .55” Segment, Red Orange, LED.Input PowerA: 110 VAC ±15% or 12 to 27 VDCB: 220 VAC ±15% or 12 to 27 VDCCurrentMaximum 28

OPERATIONSPresetsTwo control presets are provided on the unit. The presetnumbers can be made to flash without interrupting thecontrol function by pre

APPLICATIONThe unit monitors the power consumption and transmits therate, total or grand total usage upon command to a printer,PLC or computer. Eithe

4-20mA Square Law TablemA Input Pulse/Sec mA Input Pulse/Sec 4 0000 10 6123 5 2500

COUNTERThe unit accumulates up to 8 digits of batch and grand totalcount. In the setup mode choose “R0” (Reset to Zero ) foradding operation or “SP”

LOCKOUTUnauthorized front panel changes can be prevented byentering a four digit code chosen by the user in the LOCK-OUT setup mode. The unit leaves t

RS422 ELECTRICAL REQUIREMENTSThe input of the unit follows the standard E1A high imped-ance minimum of 12K Ohms. When the 422 + (A) input ismore posit

Following are two examples of requests and responses.Transmit from Receive fromTerminal Unit(S) = SpaceExample A:D13(S) Device #13[Unit #13 Activated]

The unit can supply the 24VDC to power the current loop.(Connect Pin 15 to Pin 13. Pin 16 is now + 24VDC withrespect to Pin 12). With Pin 15 connected

TABLE OF CONTENTSAPPLICATION ...

NOTE A: Unit defaults “0” K-Factor to K-Factor of “1” since it is impossible to divide by “0”.NOTE B: “Point 01”

IRREGULAR SHAPE VESSEL APPLICATION NOTE;MEASURE VOLUME IN IRREGULAR SHAPED VESSELSWITH 16-POINT LINEARIZATION OPTION.In the past it was difficult to

20

PRE A PRE B RATE/TOTAL MENUAB CD1 2 354 687 90ENT CLRAPPLICATIONBatch control, cut to length, packaging, blending. Thedisplay may be toggled between t

1- NOT USED2- SCALED OUTPUT O.C.3- ANALOG OUTPUT (SINK)4- INPUT A (PULSE/ANALOG)5- RESET INPUT6- NOT USED7- NOT USED8- NOT USED9- NOT USED10- NOT USED

PRESS DISPLAYPRESET A(FINAL PRESET) THEN FLASHING PRESET #0 FLASHES1 2 3 4 PRESET FLASHES(SAMPLE PRESET)1 2 3 4 IS ENTEREDPRESET B(PREWARN) THEN FLASH

DENTBD817ENTSTEP4SETTINGTHERATEMETERCLRCLR5ENTCLR6PRESS DISPLAYMENU FLASHES TO DEV TYPRT CNT (RATE OR COUNT)(SET UP RATEMETER) K FACTOR FLASHES; THEN

STEP6SETTINGTHE COM.OUT CARDSKIP IF NOTUSEDDDDENTCLR1 2PRESS DISPLAYMENU FLASHES TO DEV TYPLOCKOUTOUTCARD(OUTCARD SELECTED) UNIT ##UNIT 00 (AS AN EXA

STEP7SETTINGRATE ORCOUNT FORANALOGOUTPUTSKIP IF NOTUSEDDDDDENTDENTCLRPRESS DISPLAYMENU FLASHES TO DEV TYPLOCKOUTOUTCARDALG OUT(ANALOG SETUP SELECTED)

STEP9SETTINGRELAYFUNCTIONANDON TIMESPRESS DISPLAYMENU FLASHES TO DEV TYPLOCKOUTOUTCARDALG OUTOUT FREQRELAY(RELAY SELECTED) A GR TOTAL (RELAY A SET TO